OECD TG 114

OECD TG 114 is the standard ‘Viscosity of Liquids’, i.e. the viscosity of liquids, which is included in Section 1 (Physico-chemical properties) of the OECD Test Guidelines for the Testing of Chemicals. It was first adopted in 1981 and updated in 1995. It is not a test of health effects or ecotoxicity, but rather a test of physicochemical properties.

Viscosity is a measure of the resistance a liquid offers to flow. Dynamic viscosity (η) is usually expressed in the unit mPa·s (millisantipoise) and describes the internal friction of the liquid. Kinematic viscosity (ν), on the other hand, is the ratio of dynamic viscosity to density and is expressed in the unit mm²/s (santistoke). OECD TG 114 specifically covers methods for determining the viscosity of liquids exhibiting Newtonian behaviour.

The basic principle of the test is to measure the flow behaviour of the sample at a specific temperature and to calculate its viscosity. Viscosity is highly temperature-dependent; therefore, monitoring and recording the measurement temperature is of crucial importance. OECD TG 114 does not prescribe a specific method, but permits the use of suitable and validated procedures. Common methods include:

Capillary viscometer (Ubbelohde, Ostwald):

  • The flow time of a specific volume of liquid through a capillary tube is measured
  • The kinematic viscosity can be calculated directly; if the density is known, the dynamic viscosity can be determined
  • Offers high accuracy and repeatability for Newtonian fluids

Rotational viscometer:

  • The torque required to rotate a spindle in the liquid is measured
  • Can be used across a wide range of viscosities; also enables the investigation of non-Newtonian behaviour
  • Used to evaluate the change in viscosity as a function of shear rate

Falling-ball viscometer (Höppler):

  • The rate of fall of a ball in the liquid is measured
  • Suitable for viscous liquids and opaque samples
  • Viscosity is determined using a calculation based on Stokes’ law

Vibration viscometer:

  • The vibration damping of a probe in the liquid is measured
  • Enables rapid measurements with small sample volumes

Other methods:

  • Other validated techniques that have been calibrated using suitable reference substances

The basic parameters specified in the study are:

  • Dynamic viscosity (mPa·s) or kinematic viscosity (mm²/s)
  • Measured temperature (°C)
  • Shear rate (in rotational processes)
  • Details of the method and equipment used
  • Data on measurement uncertainty and repeatability

Why is this being done?

OECD TG 114 is being carried out for the following scientific and regulatory purposes:

Substance identification and characterisation: Viscosity is a characteristic physico-chemical property of a liquid and is used to confirm the identity and consistency of the substance

Determination of flow behaviour: assessment of whether the substance exhibits Newtonian or non-Newtonian behaviour

Prediction of volatility and environmental behaviour: Viscosity provides predictions regarding the substance’s behaviour in terms of dispersion, leaching and bioavailability in the environment. Classification and labelling: Viscosity is used in particular for the classification of the physical hazards of liquid products and in transport regulations. Input for further testing: Viscosity influences dosing, the choice of route of administration and the design of further tests. Product performance and quality control: Monitoring the consistency of raw materials, intermediates and finished products in production processes. Formulation development: For biotechnological and industrial products, viscosity is a key parameter for product performance. ‘Weight-of-evidence’ approach: Together with other physicochemical, toxicological and environmental data, it contributes to the holistic assessment of the substance.

OECD Guideline TG 114 does not, in itself, constitute a toxicity or hazard assessment. It enables physicochemical characterisation; the results must be interpreted in the context of other physicochemical properties, toxicological data and an exposure assessment.

We’ll take care of this

As part of our nano-testing services, we carry out viscosity measurements in accordance with OECD TG 114, applying scientific rigour and drawing on our accredited laboratory facilities and quality management system.

Our range of services includes the following:

Method selection and validation

  • Selection of the appropriate method (capillary, rotational, falling-ball or oscillation method) in accordance with the properties of the test substance (viscosity range, turbidity, Newtonian behaviour) and the regulatory requirements
  • Validation of the selected method and verification using suitable reference substances
  • Evaluation and reporting of measurement uncertainty
  • Documentation of method-specific limitations and conditions of use

Please feel free to contact Nano-Test for information on the choice of methods, sample acceptance criteria, the test plan and the reporting procedures for your viscosity measurements in accordance with OECD TG 114.