OECD TG 109
OECD TG 109 is the standard entitled ‘Density of Liquids and Solids’, which is included in Section 1 (Physico-chemical properties) of the OECD Test Guidelines for the testing of chemicals.
Density is defined as the mass per unit volume of a substance and is usually expressed in g/cm³ or kg/m³.
Relative density (or specific gravity), on the other hand, is the ratio of the density of a substance to the density of a reference substance (usually water at 4 °C) and is dimensionless. OECD TG 109 sets out methods for determining the density of both liquid and solid substances.
Das Grundprinzip der Prüfung besteht darin, Masse und Volumen der Prüfprobe bei einer bestimmten Temperatur genau zu messen und daraus die Dichte zu berechnen. Die OECD TG 109 schreibt keine bestimmte Methode vor, sondern lässt die Verwendung geeigneter und validierter Methoden zu. Zu den gängigen Methoden gehören:
The pycnometer method (liquids and solids):
- A glass pycnometer of fixed volume is filled with the sample and weighed
- For liquids, density is determined directly; for solids, it is determined using the principle of displacement
- Offers high accuracy and repeatability
Hydrostatic weighing (Archimedes’ principle):
- The solid sample is weighed in air and in a liquid
- Volume, and therefore density, are calculated using the principle of buoyancy
- Suitable for irregularly shaped solids
Hydrometer method (liquids):
- The density is read from the depth to which the densimeter is submerged in the liquid
- A quick and practical method; suitable for low-viscosity liquids
Digital density metre (oscillating U-tube):
- The change in the oscillation frequency of a glass tube filled with the sample is measured
- Enables highly accurate measurements with small sample volumes
Other methods:
- Gas pycnometer (for porous solids)
- Other validated techniques that have been calibrated using suitable reference substances
The basic parameters specified in the study are:
- Density (g/cm³ or kg/m³)
- Relative density (relative to the reference substance)
- Measured temperature (°C)
- Details of the method and equipment used
- Data on measurement uncertainty and repeatability
Why is this being done?
OECD TG 109 is being carried out for the following scientific and regulatory purposes:
Substance identification: Density is a characteristic physico-chemical property of a substance and serves as a reference value for identification
Assessment of purity and consistency: Variations in density may indicate the presence of impurities or irregularities in the manufacturing process
Determining the physical state: Density provides information about the physical state and behaviour of a substance at room temperature
Classification and labelling: Density is used in particular for the classification of physical hazards and in transport regulations for liquids
Prediction of environmental behaviour: Density provides an indication of a substance’s tendency to sink or float in water, as well as its distribution in the environment. Input for further testing: Density influences dosage calculations, the choice of route of administration and the design of further tests. Quality control: Monitoring the consistency of raw materials, intermediates and finished products in production processes. Weighing approach: Contributes to a holistic assessment of the substance in conjunction with other physicochemical, toxicological and environmental data.
OECD TG 109 is not, in itself, a toxicity or hazard assessment. It is intended for physicochemical characterisation; the results must be interpreted in the context of other physicochemical properties, toxicological data and the exposure assessment.
As part of our nano-testing services, we carry out density measurements in accordance with OECD TG 109, applying scientific rigour and utilising our accredited laboratory facilities and quality management system. Our scope of services includes the following:
Selection of the appropriate method (pycnometer, hydrostatic weighing, densimeter, digital density meter) depending on the physical state (liquid/solid) and the properties of the test substance
Validation of the selected method and its verification using suitable reference substances; assessment and reporting of measurement uncertainty; documentation of method-specific limitations and conditions of use
Please feel free to contact Nano-Test for information on the choice of methods, sample acceptance criteria, the test plan and the reporting procedures relating to your density determinations in accordance with OECD TG 109.

