CIPAC MT 184
CIPAC MT 184, published by the Collaborative International Pesticides Analytical Council (CIPAC), and formulations which form a suspension when diluted with water (e.g. wettable powder – WP, water-dispersible granules – WG, suspension concentrate – SC, water-soluble granules – SG, oil suspension – OD, etc.) is used to determine suspensibility. CIPAC is an international organisation that standardises analytical methods and physico-chemical test procedures for plant protection products; CIPAC methods are widely recognised in plant protection product authorisation dossiers, product specifications and quality control processes.
Note on regulatory status: CIPAC MT 184 is a general method that replaces the formulation-specific historical methods (e.g. MT 15 for WP, MT 75 for WG, MT 161 for SC) and is widely used in current regulatory practice. The method is applicable to all formulations that form a suspension after dilution and enables a standardised assessment regardless of the formulation type.
The basic principle of the test is as follows:
- The formulation is prepared in water of standard hardness at the concentration specified in the product specification.
- The suspension is mixed thoroughly and left to stand in a standard measuring jug or cylinder for a specified period (usually 30 minutes).
- Once the waiting period has elapsed, a sample is taken from the upper portion (usually the top 9/10 or a specified volume).
- The amount of active ingredient contained in the upper suspension is calculated in relation to the original total amount of active ingredient in order to determine the percentage of suspension (% suspensibility).
- The active ingredient is determined using an analytical method specific to the formulation (HPLC, GC, etc.).
- If required, the suspension stability after wetting and the sedimentation behaviour can also be assessed.
The key parameters reported in the study are as follows:
- Suspension capacity (%)
- Test concentration and volume of the suspension prepared
- Water hardness (usually standard hardness, e.g. 342 ppm CaCO₃) and temperature
- Residence time (usually 30 minutes) and sampling depth
- Dispersion method used (stirring speed, duration, number of cycles)
- Method for the determination of the active ingredient and analytical results
- Observations on sedimentation and flocculation
- Comparison with the specification value (if available)
- Data on measurement uncertainty and repeatability
Why is this being done?
CIPAC MT 184 is being carried out for the following scientific, technical and regulatory purposes:
- Assessment of product performance: Determination of the formulation’s ability to form a homogeneous suspension after dilution with water and to remain in suspension
- Ensuring application quality: providing essential data to ensure that the active ingredient is distributed evenly throughout the tank during spraying and does not precipitate
- Verification of compliance with the product specification: determining whether the suspension capacity meets the specified value (e.g. minimum suspension capacity in %)
- Quality control: Monitoring consistency between production batches and ensuring product quality
- Formulation development: Optimising the selection of dispersants, wetting agents, thickeners and excipients
- Assessment of storage stability: Monitoring whether the suspension properties are maintained after ageing
- Comparison independent of formulation type: Comparison of different formulation types (WP, WG, SC, etc.) using a standard method
- Support for registration dossiers: Use in pesticide registration dossiers (e.g. EU Regulation 1107/2009, national regulations) and product specifications
- Approach to assessing evidential value: a contribution to the holistic evaluation of the product in conjunction with other physico-chemical tests (wetting time, spreading time, sieve test, suspension stability, foaming, viscosity), analytical data and stability studies
CIPAC MT 184 does not, in itself, provide comprehensive information on product quality or biological efficacy. It enables a physico-chemical performance assessment; the results must be interpreted in conjunction with other formulation tests, analytical data, stability studies and the requirements of the specifications.
As part of our nano-testing services, we carry out the suspension tests specified in CIPAC MT 184 with scientific rigour, utilising our accredited laboratory facilities and quality management system. Our scope of services includes the following:
Method selection and validation
- Assessment of the suitability of CIPAC MT 184 in accordance with the formulation type and regulatory requirements
- Selection, calibration and validation of the formulation-specific method for determining active ingredients (HPLC, GC, etc.)
- Validation of the method: linearity, accuracy, repeatability and reproducibility
- Evaluation and reporting of measurement uncertainty
- Documentation of method-specific limitations and conditions of use
Please feel free to contact Nano-Test for information on method selection, analytical strategy, sample acceptance criteria, specification comparison, the test schedule and reporting procedures for your suspension capacity tests under CIPAC MT 184.

