OECD TG 115

OECD TG 115 is the standard ‘Surface Tension and Interfacial Tension of Aqueous Solutions’, i.e. the surface and interfacial tension of aqueous solutions, which is included in Section 1 (Physicochemical Properties) of the OECD Test Guidelines for the testing of chemicals.

Surface tension is defined as the force per unit length acting on the surface of a liquid in contact with air, and is usually expressed in the unit mN/m. Interfacial tension, on the other hand, is the tension that arises at the interface between two immiscible liquids. OECD TG 115 is specifically designed to determine the surface tension (at the interface with air) of aqueous solutions, as well as the interfacial tension between water and a liquid that is immiscible with water.

The basic principle of the test involves measuring the surface or interfacial tension of an aqueous solution of the test substance at a specific temperature. In the case of surfactants, the tension decreases as the concentration increases and stabilises in the region of the critical micelle concentration (CMC). For this reason, the measurements are usually carried out as a series of concentration tests.

OECD TG 115 does not prescribe any specific method, but permits the use of suitable and validated methods. Common methods include:

Ring method (du Noüy ring):

  • A platinum-iridium ring is pulled upwards from the surface of the liquid and the pull-off force is measured
  • Frequently used in the measurement of surface and interfacial tension
  • Correction factors are applied depending on the ring geometry and wetting conditions

Plate method (Wilhelmy plate):

  • A glass or platinum plate is immersed in the liquid and the force acting on it is measured
  • Offers high accuracy and repeatability when measuring surface tension
  • The contact angle and the cleanliness of the plate are of crucial importance

Drop volume/drop weight method:

  • The volume or weight of a drop falling from a capillary is measured
  • The surface and interfacial tension are calculated
  • Requires careful use with viscous or surfactant-containing solutions

Pendent-drop and spinning-drop methods:

  • The tension is determined by optical analysis of the droplet profile
  • The spinning-drop method is particularly suitable for very low interfacial tensions

Other methods:

  • Other validated techniques that have been calibrated using suitable reference substances

The key parameters reported in the study are:

  • Surface tension (mN/m) and/or interfacial tension (mN/m)
  • Test concentration and concentration series
  • Measured temperature (°C)
  • Details of the method and equipment used
  • Immiscible liquid used to determine interfacial tension (e.g. n-hexane, cyclohexane)
  • Where applicable, the CMC value and pH value
  • Data on measurement uncertainty and repeatability

Why is the test carried out?

The OECD TG 115 is being carried out for the following scientific and regulatory purposes:

  • Characterisation of surface activity: determination of the test substance’s potential to reduce surface tension and its surface-active behaviour
  • CMC determination: determination of the critical micelle concentration of surfactants; this value is important for formulation and environmental behaviour
  • Prediction of environmental behaviour: Surface tension provides insights into the substance’s film-forming, distribution and bioavailability behaviour on the water’s surface
  • Design of ecotoxicity tests: Provides information for selecting test concentrations and dosages for surfactants
  • Formulation and product performance: Evaluation of properties as a detergent, emulsifier, wetting agent and dispersant
  • Classification and labelling: Surfactant properties are taken into account in some regulatory frameworks for the classification of the substance
  • Quality control: Monitoring the consistency of raw materials, intermediate products and finished products in production processes
  • Weighting approach: a contribution to the holistic assessment of the substance in conjunction with other physicochemical, toxicological and environmental data

OECD Test Guideline 115 is not a standalone toxicity or hazard assessment.

It provides a physicochemical characterisation; the results should be interpreted in conjunction with other physicochemical properties, toxicological data and an exposure assessment.

As part of our nano-testing services, we carry out measurements of surface and interfacial tension in accordance with OECD TG 115, applying scientific rigour and drawing on our accredited laboratory facilities and quality management system. Our scope of services includes the following:

Method selection and validation

Selection of the appropriate method (ring, plate, drop volume, suspended/rotating drop) in accordance with the properties of the test substance (surface activity, expected stress range, viscosity) and regulatory requirements

Validation of the selected method and verification using suitable reference substances (e.g. pure water, reference solutions for surfactants); assessment and reporting of measurement uncertainty; documentation of method-specific limitations and conditions of use

For information on the choice of methods, the design of concentration series, sample acceptance criteria, the test plan and the reporting procedures for your surface and interfacial tension measurements in accordance with OECD TG 115, please feel free to contact Nano-Test.